固体微推力器设计与数值分析

设计了两种基于微光机电技术的固体微推力器结构,其中一种结构具有不连续的非正常拉瓦尔喷管。采用数值计算方法对不同的设计进行了内弹道、燃气流动过程和热损失的数值分析。结果表明:不连续的非正常拉瓦尔喷管同样能够将推进剂燃气加速到超声速,其比冲性能与正常拉瓦尔喷管相当;微光机电技术常用的硅材料会造成推力器比冲性能较大量级的下降,而绝热性能良好的玻璃或陶瓷材料可以有效提高微推力器的比冲性能。     

40CrMnSiMoVA钢的连续冷却组织和碳化物析出的先期效应

 低合金超高强度钢的淬火组织一般为马氏体和贝氏体组成的复合组织。钢中加硅元素加剧了贝氏体转变的不完全性,使组织更复杂。40CrMnSiMoVA钢是新型航空用超高强度钢,可采用多种热处理工艺达到不同的强度级别。为配合钢的连续冷却曲线的测定,我们用透射电镜研究了不同淬火速度下转变产物的特征及变化规律,可为改进钢的性能,合理制定热处理工艺提供理论依据。     

焊后热处理对高温运行10CrMo910钢管接头持久寿命的影响

本文通过１０ＣｒＭｏ９１０钢大口径厚壁管道高温模拟试验证实，焊后热处理是一个短时超高温运行过程，它使１０ＣｒＭｏ９１０钢管接头组织提前老化，显著降低了接头的持久寿命。试验结果表明，传统的焊后热处理工序应当取消。     

微重力下管肋式空间辐射器的整体优化分析

建立了向一重力环境下管肋式空间辐射器传热过程的数学模型，并以单质量散热量最大和热载体驱动功率最小为优化目标，对管式空间辐射器进行了优化分析。     

热沉温度场仿真研究

为了确定热沉温度场控制方法，建立了KM6热沉正常运行状态的数学模型，在MATRIX仿真平台上构造了仿真模型并求解，确定了KM6热沉温度场的动态特性和等价模型，并对热沉的设计提出了若干建议。     

Thermal-structural analysis of regenerativelycooled thrust chamber wall in reusable LOX/Methane rocket engines

To predict the thermal and structural responses of the thrust chamber wall under cyclic work,a 3-D fluid-structural coupling computational methodology is developed.The thermal and mechanical loads are determined by a validated 3-D finite volume fluid-thermal coupling computational method.With the specified loads,the nonlinear thermal-structural finite element analysis is applied to obtaining the 3-D thermal and structural responses.The Chaboche nonlinear kinematic hardening model calibrated by experimental data is adopted to predict the cyclic plastic behavior of the inner wall.The methodology is further applied to the thrust chamber of LOX/Methane rocket engines.The results show that both the maximum temperature at hot run phase and the maximum circumferential residual strain of the inner wall appear at the convergent part of the chamber.Struc tural analysis for multiple work cycles reveals that the failure of the inner wall may be controlled by the low-cycle fatigue when the Chaboche model parameter γ3 =0,and the damage caused by the thermal-mechanical ratcheting of the inner wall cannot be ignored when γ3 ＞ 0.The results of sen sitivity analysis indicate that mechanical loads have a strong influence on the strains in the inner wall.     

耐高温异氰酸酯/ 环氧树脂固化历程与性能

以异氰酸酯为固化剂固化环氧树脂,通过比较不同固化条件下固化物结构的差异,研究了异氰酸酯与环氧树脂的反应历程;改变异氰酸酯/环氧树脂体系的化学计量比(I/E),采用FTIR/ATR、DSC、DMTA等研究了固化产物的结构与性能。结果表明,异氰酸酯与环氧树脂的固化历程随着温度的升高可分为三个阶段,第一阶段为异氰酸酯的三聚反应;第二阶段是一个复杂的过程,首先环氧树脂和异氰酸酯可反应生成嗯唑烷酮结构,通过嗯唑烷酮环扩链得到端畀氰酸酯基低聚物,可继续发生三聚反应;第三阶段为异氰脲酸酯与残余的环氧基团反应生成嗯唑烷酮结构,异氰脲酸酯六元环向噁唑烷酮五元环的转化是一个可逆的过程。不同的I/E比例可得到结构不同的固化物,不同的结构导致固化物性能的差异:当(I/E)=1.8时,综合力学性能良好,异氰酸酯/环氧树脂/玻璃纤维复合材料的弯曲强度、弯曲模量、层剪强度分别为652.53、33270.63和31.66MPa,优于甲基四氢苯酐/环氧树脂/玻璃纤维复合材料力学性能;当I/E=2.0时,固化物T_g达到了305℃,明显优于传统的环氧树脂固化体系。     

Numerical analysis of hypersonic thermochemical non-equilibrium environment for an entry configuration in ionized flow

A theoretical methodology for thermochemical non-equilibrium flow combing with the HLLC (Harten-Lax-van Leer Contact) scheme was applied to study the hypersonic thermochemical non-equilibrium environment of an entry configuration in ionized flow. A two-temperature controlling model was utilized and the Gupta’s 11 species (N₂, O₂, NO, O, N, NO⁺, N₂⁺, O₂⁺, N⁺, O⁺, e^?) thermochemical non-equilibrium model was taken. Firstly, numerical calculations of hypersonic thermochemical non-equilibrium environments for different aerodynamic shapes were carried out to verify the reliability of the method above. Then, the method was used to research the effects of ionization and wall catalysis on the hypersonic thermochemical non-equilibrium environment of the entry configuration in ionized flow. The shock stand-off distance can be reduced by thermochemical reactions but doesn’t continue to decrease significantly when ionization occurs. The shock stand-off distance calculated by the 11 species model is 4.2% smaller than that calculated by the 5 species (N₂, O₂, NO, O, N) thermochemical non-equilibrium model without considering ionization. Ionization reduces wall heat flux but increases wall pressure a little. The effect of ionization on aerothermal loads is greater than that of aerodynamic loads. The thermochemical reactions of electrons and ions catalyzed at the wall increase wall heat flux significantly but make a small change in wall pressure. The maximum wall heat flux obtained by only considering the electrons and ions catalyzed at the partially catalytic wall condition is 11.8% less than that calculated at the super-catalytic wall condition.     

高主流湍流度下密度比对涡轮导叶全气膜冷却特性的影响

为了研究高主流湍流度下二次流密度比对涡轮导叶全气膜冷却特性的影响,使用热色液晶测量了在主流湍流度为15%,二次流密度比为1.0和1.5下三维涡轮导叶的气膜冷却效率和换热系数。二次流与主流质量流量比为7.0%和12.5%。结果表明:二次流密度比增大可以降低冷气射流的动量,小流量比工况下,在叶片前缘和压力面前半段,动量较低的二次流在高主流湍流度的影响下更易耗散,增大二次流密度比使冷却效率明显降低;大流量比工况下,二次流动量降低使气膜孔后区域冷气贴附性增强,气膜冷却效率和冷气覆盖效果均得到提升。小流量比工况下,二次流密度比增大对叶片表面换热的影响较小;大流量比工况下,二次流密度比增大使吸力面中弦区域和压力面后半段的平均换热系数比分别降低15%和25%。     

非线性能量阱对飞轮振动抑制效果的实验研究

利用薄片金属梁作为非线性刚度元件，构建一种非线性能量阱。为了验证非线性能量阱对飞轮振动特性的抑制效果，搭建地面飞轮测试系统。分别采用力锤敲击和飞轮以恒定转速运行的方法施加不同载荷，对安装非线性能量阱前后测试系统各典型位置的振动响应进行对比研究。利用实测数据，采用傅里叶变换方法将动态响应信息分别在时间域和频率域内展开。研究表明：力锤敲击产生的冲击载荷和飞轮以恒定转速运行产生的稳态载荷均可以激发非线性能量阱定向能量传输；受非线性能量阱的影响，柔性支架设备安装面和飞轮安装面振动响应得到有效抑制。但是，由于非线性能量阱阻尼和吸振子质量较小，不同程度削弱了其振动抑制效果。